New submissions from readers:
I was wondering you thoughts on Mature Metal’s Jailbird outfitted with one of the anti-pullout pins (maybe even a second base ring) vs. a Steelheart with the penisring (http://steelworxx.de/Penisring-51p.html).
I know without a PA piercing the inescapable trapped ball device doesn’t exist, but I want to get as close as possible. I have seen mixed reviews on MM’s anti-pullout pins but I’ve seen absolutely nothing about Steelworxx’s penisring. Frankly, I don’t see how the ring would stay on when flaccid but I’m still curious about it.
I am currently locked in a Birdlocked Mini, my first device, and am looking to purchase my next device… one of the above hopefully. Since you are coming from a place of experience I would love your take on the two devices described above.
Both those devices work by trying to bunch up the flaccid penis skin making pull out more difficult, not unlike the KSD-G3 for the CB6K. The KSD is the only thing I have first-hand experience with and it does make things a bit more secure down there (and feel more secure, which may be more important since security absent a piercing is mostly in one’s head), though, of course, a few seconds of fiddling in the shower can defeat all these kinds of devices. The downside to the KSD is that it would often leave abrasions on the shaft of the penis from when it would try to become hard in the CB6K and press against it with some force. I would assume MM’s anti-pull out pins would be even more likely to do something similar. Honestly, I never liked the look of them. They seem like they’d be quite painful (and not in the good way). The Steelworxx penis ring might be somewhat more gentle, but again, I’ve never used one. I considered it back in the day, but by the time I ordered I already had the PA and didn’t need it.
I wonder if one of these guys couldn’t fashion a KSD-like insert out of stainless? I know Dietmar at Steelworxx will try anything, but the cost might be prohibitive.
Here’s another question along similar lines…
I have been reading some (not all) entries of your blog and found them very informative. I myself am into chastity play with my wife. We only started very recently (last year) and my first device was a Looker 02 from Steelworxx with the penis-plug. The plug did extend quite a bit (around 1″) through the A-Ring, so this added a lot of security.
However for various reasons I needed to be circumcised. Now the scars are healing and me and my wife will get pierced. I will get a PA and she will get a vertical hood piercing.
Since the Looker with the penis-plug is not possible with a PA and we were intrigued by the added PA-security, we plan on getting a Steelheart (or Steelheart 2) with an internal PA-fixture (the one you designed).
I hope you don’t mind me asking you a few questions since it seems you actually own and wear just that type of device.
Basically it is about measuring. I am unsure about the length of the device. When measuring for the Looker I took the total flaccid length and subtracted half an inch. This worked quite well and the tip was comfortable at the front nearly all the times. For diameter I chose the flaccid diameter plus the Plug-diameter. However this turned out to be slightly on the loose side. It was no problem and it was comfortable but there was a little space around while flaccid.
Anyway, my questions are, how do you measure the length and diameter when you have a PA? Do you need to add a bit to the length and diameter to accommodate the PA?
How far do you think you can pull the device down while wearing it. Do you fear ppl. with shorter tools than yours would be able to access the PA?
Sorry for babbling at you and I hope it is not too much trouble to share your information. But you seem to be the only source I can find 🙂
When I measured for our second Steelheart I went much shorter on the tube but added a bit to my normal flaccid length since I needed to accommodate the PA ring and the fixing. In truth, I may have added too much. In my opinion, you probably shouldn’t make it shorter than your normal flaccid length. The circumference is trickier since you also want to leave room in there for the fixing which does take some of the space up. I find the penis will sometimes knock around inside the tube I wear, but it’s often. I don’t think I’d want it any tighter. You also need to think about pinching and such. I assume that less circumference would make that more prevalent.
So, short story, keep it just a bit longer than your flaccid length and just a tad bigger around. The other thing you need to think about is the gauge of the ring. My PA accommodates 4 GA jewelry, but if I wear a ring that big while in the device I get too much pinching at the end. If I scale back to 8 GA, things are a lot better.
Regarding how much I can pull out, I can get just to the edge of the penis’s corona, but that’s it (see for yourself). You don’t need to worry about getting tools down there. It’s impossible. Even if you could somehow get the ball out of the ring, you’d never ever get it back in and would eventually get busted. There’s not nearly enough room in there to maneuver. That said, I don’t think getting the ring out is even possible. That would be an advantage of using a thicker ring since the ball would be really hard to remove without tools. Hope that helps.
Question about your Looker 02. How long were you able to wear it at a stretch? Did the urethral tube ever cause you any problems?
Question, comment or general chit-chat? Use the feedback page!